Engineering Guide · Variable-frequency drives

VFD or soft starter: which is appropriate?

A soft starter limits the starting transient, whereas a variable-frequency drive regulates motor speed during operation. Selection also considers motor current, cooling, harmonics and the process duty.

Updated: 19 November 2026Reading time: 6 min
VFD or soft starter: which is appropriate? — concept illustration

Two different functions

A soft starter limits electrical and mechanical stresses during motor acceleration. A variable-frequency drive (VFD) changes supply frequency and voltage to control operating speed and, in suitable applications, torque. These devices cannot be compared solely by rated motor power.

When a soft starter is enough

Consider a soft starter if the machine normally runs at fixed speed and the problem is high starting current or torque shock—for instance, on certain pumps, fans or conveyors. Some designs bypass their power electronics after starting. The motor is then not speed-controlled.

When a VFD is justified

A VFD suits applications needing controlled flow, pressure or speed, gradual stopping or closed-loop process regulation. Variable speed may reduce energy use in centrifugal pumps or fans, but the actual saving depends on the hydraulic system, operating points, duty cycle and efficiency.

VFD or soft starter: which is appropriate?
Concept illustration only; not an approved installation or certified engineering drawing.

Limitations and electrical risks

VFD switching introduces voltage harmonics, electromagnetic interference and potentially higher motor-insulation stress. Check cable length, output filters, grounding, bearing currents, motor cooling at low speed and cabinet temperature. Both devices need properly coordinated protection.

Selection data

Use the motor nameplate current and voltage, supply characteristics, starting load, required starting torque, starts per hour, speed range, braking needs, cable run and control interfaces. Compare the motor manufacturer’s limits; GOST IEC 60034-1-2024 concerns rotating-machine rating and performance, not a universal VFD selection recipe.

Simple decision rule

If you only need gentler starting at constant operating speed, evaluate a soft starter. If you need adjustable speed during normal operation, evaluate a VFD. Verify the conclusion against load torque, protection and process requirements.

Procurement checklist

Request the motor plate, single-line circuit, torque/speed curve, site ambient temperature, EMC requirements, communication protocol, enclosure rating, expected duty cycle and commissioning responsibilities.

Verified standards and scope

Sources are official Rosstandart registry entries. Verify the current amendments and applicability to the particular project and jurisdiction.

Frequently asked questions

Principle and application?
A soft starter limits the starting transient, whereas a variable-frequency drive regulates motor speed during operation. Selection also considers motor current, cooling, harmonics and the process duty.
Design and selection?
The final design must be based on project calculations, site conditions, compatibility, maintenance access and the equipment data sheet.
Can the illustration be used as an installation drawing?
No. The image explains the concept; design and installation require approved drawings, calculations and equipment documentation.

Read next

Heat tracing pipelines in freezing weather — concept illustration
North and Arctic

Heat tracing pipelines in freezing weather

Insulation slows heat loss but does not generate heat. Electric heat tracing or a heated companion line requires heat-loss calculations, controls and appropriate electrical.

Reading time: 6 min
Low-NOx burners: principles and selection — concept illustration
Boiler equipment

Low-NOx burners: principles and selection

Low-NOx burners control peak flame temperature and mixing using staged combustion and sometimes flue-gas recirculation. Actual NOx, CO and oxygen levels require measurements.

Reading time: 6 min
Internal pontoon or external floating roof: comparison — concept illustration
Tank equipment

Internal pontoon or external floating roof: comparison

An internal floating pontoon sits below a fixed roof; an external floating roof is exposed to rain and snow and needs drainage. Both reduce vapor space, but their engineering.

Reading time: 6 min
Axial, angular or lateral expansion joint: how to choose — concept illustration
Expansion joints

Axial, angular or lateral expansion joint: how to choose

An axial joint takes movement along the pipe, an angular joint permits controlled rotation, and a lateral joint takes transverse displacement. Anchors, guides and pressure.

Reading time: 6 min
Frost-covered pipeline in severe cold during the polar night
North · Pipelines

Metal at −50 °C: Cold Brittleness and Steels for the North

Why steel breaks like glass in frost, and how to choose metal for northern pipelines and equipment.

Reading time: 6 min
Vertical steel tank with a sampler at its base
Tank equipment

PSR Tank Sampler: How It Works and How to Choose

How to take a composite sample of a petroleum product across the full tank height without climbing onto the roof.

Reading time: 5 min
Steel flanges of different types
Pipelines

Flanges per GOST 33259: Types and Sealing Faces

Plate or weld neck, face B or tongue and groove: flange types and sealing faces explained.

Reading time: 6 min
Ground thermosiphons: passive cooling without power — concept illustration
North and Arctic

Ground thermosiphons: passive cooling without power

Passive thermosiphons transfer ground heat to cold outdoor air by evaporation and condensation. They operate mainly in winter; foundation design requires thermal calculations.

Reading time: 6 min
Industrial gas burner on a steam boiler
Boiler equipment

Two-Stage or Modulating Burner: Which to Choose

Stages, progressive and smooth control: how the output control method affects fuel consumption and boiler life.

Reading time: 5 min
Field fuel depot of soft tanks at an Arctic oil field
Tanks · North

Soft Fuel Tank for the North: How to Choose

Fabric, cold resistance, volume, fittings and site — what to check so a soft tank survives an Arctic winter.

Reading time: 6 min
Installers fitting a bellows expansion joint on a pipe rack
Expansion joints

Bellows Expansion Joint Installation: 7 Common Mistakes

Misalignment, forgotten shipping restraints, welding current through the convolutions and 4 more mistakes — plus a correct installation checklist.

Reading time: 6 min
Pipelines in different identification colors on a boiler house pipe rack
Pipelines

Pipeline Identification Colors per GOST 14202: Cheat Sheet

Green for water, red for steam, yellow for gas. Identification colors, warning rings and painting rules.

Reading time: 5 min
Pipeline on supports above snow-covered tundra
North and Arctic

Pipelines on Permafrost: How They Are Built in the North

Why pipes in the North stand on supports, how thermosiphons work and how to compensate a range from −50 to +130 °C.

Reading time: 6 min
Variable frequency drives of different ratings in an electrical room
Drives

How to Size a Variable Frequency Drive

Why drives are sized by current, not kilowatts, normal and heavy duty, installation conditions and the options you need.

Reading time: 6 min
Breather valve on the roof of a vertical steel tank in winter
Tanks

Tank Breather Valve: How It Works

Why a tank breathes, how the valve works, which types exist and how to choose by flow capacity.

Reading time: 5 min
Bellows expansion joints of different types in a warehouse
Expansion joints

How to Choose a Bellows Expansion Joint: 7 Parameters

Type, diameter, pressure, movement, medium, end connection and cycle life — and what to send the supplier for accurate selection.

Reading time: 6 min
Steel pipeline with a bellows expansion joint on an industrial pipe rack
Expansion joints

How to Calculate Thermal Expansion of a Pipeline

The ΔL = α·L·Δt formula, coefficients for different materials, a worked example and an online calculator for expansion joint movement.

Reading time: 6 min
Damaged bellows expansion joint on a pipeline, close-up
Expansion joints

Why Bellows Fail: 8 Causes of Expansion Joint Failure

Excessive movement, torsion, supports, corrosion, vibration and installation errors — plus a checklist to avoid them.

Reading time: 7 min
Pump station with variable frequency drive cabinets
Drives

Variable Frequency Drive on a Pump: How Much It Saves

Why power drops with the cube of speed, a worked example and a savings and payback calculator.

Reading time: 6 min
← All guide articles

Request equipment selection

Send the project parameters for an engineering review.

Request equipment selection